2.The panel is held by clips at the center and rear section as shown. Begin by  lifting panel from the front to unstuck it from the center console. Then  disconnected the clips by pulling the entire panel backwards.

3.The filter is located in the rearward area of the center console. Remove the  filter access door by depressing the locking tab to release. Set filter access  door aside.

4.Slide out the old filter by grabbing the bottom corner, then pull and squeeze  the filter out through the slot. Install new  filter by squeezing the filter  through the opening. Ensure that the Air Flow arrow is pointing towards the rear  of the vehicle.

5.Reinstall in reverse order.

NOTE: It is not necessary to remove the top two screws for the  glove box striker.

2.Remove the glove box assembly to access the cabin air  filter cover in the upper right.

3.Remove the cover’s retaining screw, then the cover to  access the cabin air filters.

4.To remove the first filter pull straight out and then slide the second filter to the left and pull straight out.

5.Install new cabin air filters by inserting the first filter and sliding it over to the right, then install the second filter.

NOTE: Air flow arrow should face down when installed.

6.Reattach the cabin air filter cover.

7.Reattach the glove box assembly.

8.Close the glove compartment.

2.Pull out the spark plugs wires.

3. You will need a 5/8 socket, extension and ratchet to remove the spark plugs.

4. Remove #1 spark plugs.

5.Repeat the above steps for spark plugs #2, #3 and #4.

6.Reinstall new spark plugs wires.

7. Reinstall the car battery.

.
2.Pull panel outwards to release. Place panel aside.

3.Remove the filter access door by pulling the locking tab  and swinging it outwards. Place access door aside.

4.Remove filter by squeezing the sides of the old filter  softly while pulling it out towards the left.

5.Install new filter by squeezing the sides and pushing it  into the cavity. Ensure that the Air Flow arrow is pointing towards the back of  the car.

6.Reinstall in reverse order.

1.Start by removing the glove box latch. 2 screws and it’s out.

2.Next, remove the 4 screws holding the glove box in place. There are 2 at the top  and 2 at the bottom. You will have to disconnect the glove box  light, and the  air bag connector. Both come off easily, and the entire glove box can be  removed.

3.Once the glove box is out, the next step is to pop off the metal clip holding  the white filter cover in place.

4.Now the filter can be slid out. Apparently, the micro filter put in at the  factory is a single piece, and does not look like the factory replacement  filters you will put back in. In fact, the replacement filters look much nicer  (higher quality). This picture shows the empty hole where the old  filter was.

5.This side-by-side shows the stock filter removed on the left, and the  replacement filters on the right. I was quite amazed at how dirty this filter  got. The replacement filters come in two pieces, and have plastic holders that  enable them to slide into place more easily than the original filter.

My filter had all sorts of black dirt, crud and leaf pieces in it!!! And I  keep this car garaged, and never drive it in the rain (if I can help it).

6.The easiest way to get the new filters in is to put one in at the bottom, then  once it is in, slide it up into the top position, since it is  difficult to get  the proper angle to put the top one in directly.

7.Here is the completed filter installation, with both filters securely in place.  Replace the white filter cover, glove box, reconnect the light and  air bag  connectors, and this installation is complete. Ahhhh, fresh air to breathe once  again.

2.Disconnect the electrical connector at the top of the glove  box to allow glove box to be completely removed. Set glove box aside.

3.Pull on the tab at the top of the filter access door, then  push up slightly to release the door.

4.Grab on the handle and slide out the old filter towards the  right. Replace with new filter, ensuring that the Up arrow is pointing up.

5.Reinstall in reverse order.

• Open glove box door (1), remove the glove box assembly screws (A).

• Remove the glove box assembly lower screws (A).

• Disconnect the trunk switch and glove box lamp connectors, then remove the glove box assembly.
• Install in the reverse order of removal

2. Remove console lid side finisher on the passenger side

3.The panel is held by 3 clips in the front and 1 clip in the rear. Pull the panel from the front, releasing the 3 clips and pull back to disconnect the clip in the rear.

4.The filter is located in the rearward area of the center console. Remove the filter access door by depressing the locking tab to release.

5.Slide out old filter by pulling on the tab and squeezing the filter through the slot.

6.Install new filter by squeezing the filter through the opening. Ensure that the pull tab is on the bottom and that the Air Flow arrow is pointing towards the rear of the vehicle.
7.Install in the reverse order of removal.